The CEC Sanford lobby will be closed until further notice due to staffing shortages related to illness. The Sanford Drive Thru window and the Enterprise lobby are open during regular business hours. We apologize for any inconvenience.
DIY Energy Audit
While a professional home energy audit is the best way to determine where your home is losing energy and where you can save, you can conduct your own simple but diligent walk-through and spot many problems in any type of house. This “do-it-yourself” home energy audit will not be as thorough as a professional home energy assessment, but it can help you pinpoint some of the easier areas to address. When walking through your home, keep a checklist of areas you have inspected and problems you found. This list will help you prioritize your energy efficiency upgrades. Do not assume that just because your home is recently constructed–or even new–that there are no opportunities to save energy. Energy-saving technology has evolved rapidly over the past few years.
- First, make a list of obvious air leaks (drafts). The potential energy savings from reducing drafts in a home may range from 5% to 30% per year, and the home is generally much more comfortable afterward.
- Check for indoor air leaks, such as gaps along the baseboard or edge of the flooring and at junctures of the walls and ceiling. Also check for leaks on the outside of your home, especially in areas where two different building materials meet.
- You should plug and caulk holes or penetrations for faucets, pipes, electric outlets, and wiring. Look for cracks and holes in the mortar, foundation, and siding, and look for leaks around windows and doors. Seal them with the appropriate material.
- When sealing any home, you must always be aware of the danger of indoor air pollution and combustion appliance “backdrafts.” Backdraft is when the various combustion appliances and exhaust fans in the home compete for air. An exhaust fan may pull the combustion gases back into the living space. This can obviously create a very dangerous and unhealthy situation in the home.
- In homes where a fuel is burned (i.e., natural gas, fuel oil, propane, or wood) for heating, be certain the appliance has an adequate air supply. Generally, one square inch of vent opening is required for each 1,000 Btu of appliance input heat. Burn marks or soot around the appliance burner or at the vent collar, or visible smoke anywhere in the utility room while the appliance is operating, indicate poor draft. When in doubt, contact your local utility company, energy professional, or ventilation contractor.
- Heat loss through the ceiling and walls in your home could be very large if the insulation levels are less than the recommended minimum. When your house was built, the builder likely installed the amount of insulation recommended at that time. Given today’s energy prices (and future prices that will probably be higher), the level of insulation might be inadequate, especially if you have an older home.
- If the attic hatch is located above a conditioned space, check to see if it is at least as heavily insulated as the attic, is weather stripped, and closes tightly. In the attic, determine whether openings for items such as pipes, ductwork, and chimneys are sealed. Seal any gaps with an expanding foam caulk or some other permanent sealant. When sealing gaps around chimneys, or other heat producing devices, be sure to use a non-combustible sealant.
- While you are inspecting the attic, check to see if there is a vapor barrier under the attic insulation. The vapor barrier might be tar paper, Kraft paper attached to fiberglass bats, or a plastic sheet. If there does not appear to be a vapor barrier, you might consider painting the interior ceilings with vapor barrier paint. This reduces the amount of water vapor that can pass through the ceiling. Large amounts of moisture can reduce the effectiveness of insulation and promote structural damage.
- Make sure that the attic vents are not blocked by insulation. You also should seal any electrical boxes in the ceiling with flexible caulk (from the living room side or attic side) and cover the entire attic floor with at least the current recommended amount of insulation.
- If your basement or crawlspace is unconditioned and open to the exterior, determine whether there is insulation under the living area flooring. In most areas of the country, an R-value of 25 is the recommended minimum level of insulation. If the sub-space is enclosed and contains heating or cooling appliances, air ducts or plumbing, you should probably insulate the sub-space perimeter rather than the living space floor. The insulation at the top of the foundation wall and first-floor perimeter should have an R-value of 19 or greater. If the basement is intentionally conditioned, the foundation walls should also be insulated to at least R-19. Your water heater, hot water pipes, and furnace ducts should all be insulated.
- Inspect heating and cooling equipment annually, or as recommended by the manufacturer. If you have a forced-air furnace, check your filters and replace them as needed. Generally, you should change them about once every month or two, especially during periods of high usage. Have a professional check and clean your equipment once a year.
- If the unit is more than 15 years old, you should consider replacing your system with one of the newer, energy-efficient units. A new unit would greatly reduce your energy consumption, especially if the existing equipment is in poor condition. Check your ductwork for dirt streaks, especially near seams. These indicate air leaks, and they should be sealed with a duct mastic. Insulate any ducts or pipes that travel through unheated spaces. An insulation R-Value of 6 is the recommended minimum.
- Energy for lighting accounts for about 10% of your electric bill. Examine the light bulbs in your house and consider replacing inefficient bulbs with a more efficient choice, such as energy-saving incandescent, compact fluorescent lamps (CFLs), or light-emitting diodes (LEDs). When shopping for bulbs, consider the brightness of the bulbs you want and look for lumen and the Lighting Facts label.
- The appliances and electronics you choose and how you use them affect your energy use and costs. Examine the appliances and electronics in your home and estimate their energy use. Consider strategies for reducing the energy use of your appliances and electronics.
You might consider the following:
- Unplugging an item when it is not in use to prevent phantom loads
- Changing the settings or using the item less often
- Purchasing a new, more efficient product.